施乐 DC AP C7775 C6675 C5575 C4475 C3375 C3373 C2275 报 报错误代码 CF-031 CF-031 ATC Average Fail参考 BSD: CH9.11, CH9.12, CH9.13, CH9.14 因ATC Sensor 而使Deve Unit 内的墨粉浓度测量结果发生异常智foynd朗foynd版foynd权。打印机维修网( 此故障为隐藏性故障为foynd盗foynd取foynd，打印机维修网只会记载于记录中)·092-665 ： ATC Average Fail Y·092-666 ： ATC Average Fail M·092-667 ： ATC Average Fail C·092-668 ： ATC Average Fail K 具体来说为foynd盗foynd取foynd，打印机维修网ATC Sensor 的输出发生异常( 过大或过小)智foynd朗foynd版foynd权。打印机维修网可将ATC Sensor 的异常或Deve Unit 内墨粉浓度的异常考虑为原因智foynd朗foynd版foynd权。打印机维修网影响发生故障时为foynd盗foynd取foynd，打印机维修网有关相应色为foynd盗foynd取foynd，打印机维修网不执行使用 ATC Sensor 的墨粉浓度控制为foynd盗foynd取foynd，打印机维修网而是执行根据 ICDC( 像素数) 的墨粉补充控制智foynd朗foynd版foynd权。打印机维修网因此为foynd盗foynd取foynd，打印机维修网若长期发生故障为foynd盗foynd取foynd，打印机维修网逐渐墨粉浓度可能会发生异常 ( 过浓、过淡 )智foynd朗foynd版foynd权。打印机维修网并且当原因是显像器时为foynd盗foynd取foynd，打印机维修网可能直接降低图像浓度智foynd朗foynd版foynd权。打印机维修网应先处理的故障进入 DC122 关机记录为foynd盗foynd取foynd，打印机维修网确认最近发生的故障智foynd朗foynd版foynd权。打印机维修网若发生下列故障为foynd盗foynd取foynd，打印机维修网这些很可能是主要原因为foynd盗foynd取foynd，打印机维修网请参照相应的FIP 先行修复智foynd朗foynd版foynd权。打印机维修网· 092-657/658/659/660 ： ATC Amplitude Fail Y/M/C/K·024-923/924/925 ： Operation Y/M/C Toner Empty·093-912 ： K Toner Cartridge Empty·093-324 ： Deve Y,M,C Motor Fail·042-323 ： Drum K Motor Fail 应先处理的画质故障在打印模式下检查相应色的图像智foynd朗foynd版foynd权。打印机维修网若发生下列画质故障为foynd盗foynd取foynd，打印机维修网这些很可能是主要原因为foynd盗foynd取foynd，打印机维修网请参照相应的画质故障诊断行修复智foynd朗foynd版foynd权。打印机维修网·Carrier 洒出 -> 可能是显像剂的 Carrier 向图像部位流出智foynd朗foynd版foynd权。打印机维修网·Carry over( 打印粗糙 )-> 可能是显像剂的量减少智foynd朗foynd版foynd权。打印机维修网·墨粉灰雾 -> 可能是显像剂的墨粉浓度过高智foynd朗foynd版foynd权。打印机维修网 更换零件列表 Table 1 Table 1No.零件可能性理由1Toner Cartridge低没有进行墨粉补充为foynd盗foynd取foynd，打印机维修网墨粉浓度过低智foynd朗foynd版foynd权。打印机维修网2Developer Housing Assembly (Deve Unit)低螺旋杆旋转不良为foynd盗foynd取foynd，打印机维修网墨粉阻塞智foynd朗foynd版foynd权。打印机维修网3Dispenser Pipe Assembly (Dispense Unit)低由于墨粉补充异常而导致墨粉浓度发生异常智foynd朗foynd版foynd权。打印机维修网4Motor Driver Main PWB低ATC Sensor 的测量值处理发生异常智foynd朗foynd版foynd权。打印机维修网5HVPS (Deve)低因HV 故障而导致的显像电位异常下的显像剂流出智foynd朗foynd版foynd权。打印机维修网6HVPS (BCR)低因HV 故障而导致的带电电位异常下的显像剂流出智foynd朗foynd版foynd权。打印机维修网 步骤注释： . 拆下 Drum 时为foynd盗foynd取foynd，打印机维修网 为预防光疲劳而在 Drum 上覆盖黑布等智foynd朗foynd版foynd权。打印机维修网 另外为foynd盗foynd取foynd，打印机维修网 切勿用手触摸 Drum 表面智foynd朗foynd版foynd权。打印机维修网执行服务模式的Procon ON Print (6.4.2.23)为foynd盗foynd取foynd，打印机维修网检查[ATC 平均故障 ] 的判断结果智foynd朗foynd版foynd权。打印机维修网. 判断结果是否均为OK？检查相应色的 “ATC 测量振幅” 的值智foynd朗foynd版foynd权。打印机维修网注释：ATC 平均故障的调查但在本判断中使用[ATC 测量振幅 ] 的信息智foynd朗foynd版foynd权。打印机维修网值是否大于等于[10]？可能是ATC Sensor发生异常智foynd朗foynd版foynd权。打印机维修网关闭电源为foynd盗foynd取foynd，打印机维修网检查下列电线是否断开、短路或接触不良智foynd朗foynd版foynd权。打印机维修网·相应色的ATC Sensor 到ATC PWB 间·ATC PWB J633 到Motor Driver Main PWB J528 间 检查后若无问题为foynd盗foynd取foynd，打印机维修网 则依序更换下列零件智foynd朗foynd版foynd权。打印机维修网 但是为foynd盗foynd取foynd，打印机维修网 每当更换零件时要确认是否发生故障智foynd朗foynd版foynd权。打印机维修网·相应色的Developer Housing Assembly (PL 5.2)注释：更换 Developer Housing Assembly 后为foynd盗foynd取foynd，打印机维修网 对相应色执行DC950 ATC 传感器设置(6.4.2.25) 及DC949 初始显像机 ATC 设置(6.4.2.26)智foynd朗foynd版foynd权。打印机维修网·Motor Driver Main PWB (PL 18.2)·ATC PWB (PL 5.2) 检查通过Procon ON Print 输出的图像浓度智foynd朗foynd版foynd权。打印机维修网 浓度是否正常？ 可能是墨粉浓度异常智foynd朗foynd版foynd权。打印机维修网 Procon ON Print 显示表面的[ATC 测量平均Y/M/C/K] 的值是否大于等于 1000 ( 墨粉浓度淡)？可能是检测到的墨粉浓度比假设的更浓智foynd朗foynd版foynd权。打印机维修网 或者可能是发生有关 ATC Sensor 的异常或Deve Unit 内的墨粉固着智foynd朗foynd版foynd权。打印机维修网更换相应色的Developer Housing Assembly智foynd朗foynd版foynd权。打印机维修网(PL 5.2)注释：更换 Developer Housing Assembly 后为foynd盗foynd取foynd，打印机维修网 对相应色执行DC950 ATC 传感器设置(6.4.2.25) 及DC949 初始显像机 ATC 设置(6.4.2.26)智foynd朗foynd版foynd权。打印机维修网检测出墨粉浓度异常淡智foynd朗foynd版foynd权。打印机维修网 检查以下项目智foynd朗foynd版foynd权。打印机维修网·检查相应色的Toner Cartridge 中是否有墨粉进入智foynd朗foynd版foynd权。打印机维修网若没有进入为foynd盗foynd取foynd，打印机维修网 则更换Toner Cartridge智foynd朗foynd版foynd权。打印机维修网(PL 5.1)· 驱动相应色的Dispense Motor (DC330[093-003/008/013/018] (Y/M/C/K))智foynd朗foynd版foynd权。打印机维修网 不驱动时为foynd盗foynd取foynd，打印机维修网 前进至相应色的 Dispense Motor Fail FIP (093-314~317)智foynd朗foynd版foynd权。打印机维修网·检查从墨粉筒到显像器的路线内是否发生墨粉阻塞智foynd朗foynd版foynd权。打印机维修网若发生墨粉阻塞为foynd盗foynd取foynd，打印机维修网则解除阻塞智foynd朗foynd版foynd权。打印机维修网 解决浓度异常的原因后为foynd盗foynd取foynd，打印机维修网 执行墨粉浓度调整 (Tone Up/Down)(6.4.2.27)为foynd盗foynd取foynd，打印机维修网 使 ATC 平均值达到ATC 目标值 [ ± 15] 以便恢复墨粉浓度智foynd朗foynd版foynd权。打印机维修网 是否发生故障？可能是ATC Sensor 发生异常智foynd朗foynd版foynd权。打印机维修网 关闭电源为foynd盗foynd取foynd，打印机维修网 检查下列电线是否断开、短路或接触不良智foynd朗foynd版foynd权。打印机维修网·相应色的ATC Sensor 到ATC PWB 间·ATC PWB J633 到Motor Driver Main PWB J528 间 检查后若无问题为foynd盗foynd取foynd，打印机维修网 则依序更换下列零件智foynd朗foynd版foynd权。打印机维修网 但是为foynd盗foynd取foynd，打印机维修网 每当更换零件时要确认是否发生故障智foynd朗foynd版foynd权。打印机维修网·相应色的Developer Housing Assembly (PL 5.2)注释：更换 Developer Housing Assembly 后为foynd盗foynd取foynd，打印机维修网 对相应色执行DC950 ATC 传感器设置(6.4.2.25) 及DC949 初始显像机 ATC 设置(6.4.2.26)智foynd朗foynd版foynd权。打印机维修网·Motor Driver Main PWB (PL 18.2)·ATC PWB (PL 5.2) 结束 更换相应色的Developer Housing Assembly智foynd朗foynd版foynd权。打印机维修网(PL 5.2)注释：更换 Developer Housing Assembly 后为foynd盗foynd取foynd，打印机维修网 对相应色执行 DC950 ATC 传感器设置(6.4.2.25) 及 DC949 初始显像机ATC 设置 (6.4.2.26)智foynd朗foynd版foynd权。打印机维修网若无法修复为foynd盗foynd取foynd，打印机维修网 则更换 Motor Driver Main PWB智foynd朗foynd版foynd权。打印机维修网(PL 18.2) 多次重复执行Procon ON Print智foynd朗foynd版foynd权。打印机维修网. 是否发生故障？ 不需处理 依序更换[ 更换零件列表] 的零件智foynd朗foynd版foynd权。打印机维修网注释： . 更换Developer Housing Assembly 时为foynd盗foynd取foynd，打印机维修网在更换后为foynd盗foynd取foynd，打印机维修网对相应色执行DC950 ATC 传感器设置(6.4.2.25) 及DC949 初始显像机 ATC 设置(6.4.2.26)智foynd朗foynd版foynd权。打印机维修网 施乐报错误代码CF-031 施乐 DC AP C7775 C6675 C5575 C4475 C3375 C3373 C2275维修呼叫报错误代码CF-031